Minnesota Focus Owners Club

Hey,
Looking for any info on mating a focussport front lip onto a svtbumper.
Any info from other sites would be greatly appreciated, or if you could post on there for me, it would be very appreciated.

Thanks!
Corey

It should be similar to putting a Mustang Mach lip on an SVT bumper. Rivets or self-tapping screws and patience.

Never seen it done. They made of fiberglass and carbon fiber (read no flex like the Mach 1) so it best be a direct fit. You will be it hero if you pull it off, but they are already so rare since they were discontinued 3-4 years ago, they are real hard to come by. If you already have one, hang tape it into place to check the fitment. If it's a go, a mix of 3m double sided tape may help, but screws are definitely in your future.

HotRodWagon wrote:Never seen it done. They made of fiberglass and carbon fiber (read no flex like the Mach 1) so it best be a direct fit. You will be it hero if you pull it off, but they are already so rare since they were discontinued 3-4 years ago, they are real hard to come by. If you already have one, hang tape it into place to check the fitment. If it's a go, a mix of 3m double sided tape may help, but screws are definitely in your future.

Ya' learn something new every day. I didn't know they were made of glass.

Well thats not much help!
I started today and im thinking ill just have to make a few sheet metal brackets. Hope it goes well.

Slowly but surely haha

When i bought it off you, you said its been done. I did see the picture you had up, but it looks like it may have been deleted.

this may be impossible. seems too short, contemplating cutting the ends off.....

If they're rare I would try to sell it before hacking it up.

who cares its slow and ugly and stupid. it a focus they are a girls car. fuck im pissed

what happened?

WASaZX3pos wrote: When i bought it off you, you said its been done. I did see the picture you had up, but it looks like it may have been deleted.

First off I have never sold an FS lip, ever. You bought a Ford Accessory/S2 lip.

Second, I did say it has been done, and posted the pictures. I also said I did not know how it was installed/what was done to install it, nor what the fit would be like, other than it has been fitted as seen in the pictures.

HotRodWagon wrote:

WASaZX3pos wrote: When i bought it off you, you said its been done. I did see the picture you had up, but it looks like it may have been deleted.

First off I have never sold an FS lip, ever. You bought a Ford Accessory/S2 lip.

Second, I did say it has been done, and posted the pictures. I also said I did not know how it was installed/what was done to install it, nor what the fit would be like, other than it has been fitted as seen in the pictures.

Seems pretty clear cut to me.

FORDSVTPARTS wrote:

HotRodWagon wrote:

WASaZX3pos wrote: When i bought it off you, you said its been done. I did see the picture you had up, but it looks like it may have been deleted.

First off I have never sold an FS lip, ever. You bought a Ford Accessory/S2 lip.

Second, I did say it has been done, and posted the pictures. I also said I did not know how it was installed/what was done to install it, nor what the fit would be like, other than it has been fitted as seen in the pictures.

Seems pretty clear cut to me.

huh?

WASaZX3pos wrote:

Seems pretty clear cut to me.[/quote]

huh?[/quote]

The lip you bought is an old Ford accessory kit, not an FS lip.

The picture Hotrodwagon posted is of an SVT with that lip on it to show that it has been done, it's up to you to figure out how to do it though.

-Steve


.

someone somewhere has to know something.

What's the problem you seem to be having?