Page 5 of 7

Re: zx3 almost done

Posted: Mon Mar 08, 2010 12:41 pm
by hermitmaster
Patalrob wrote: Image
Is that a photo of Turbo Tom? :lol:

Re: zx3 almost done

Posted: Mon Mar 08, 2010 1:09 pm
by KRYPTO
be nice

Re: zx3 almost done

Posted: Mon Mar 08, 2010 1:13 pm
by WASaZX3pos
Just to let you know, i asked if you had it off, i did tighten it. Cause if you had it off at some point, this would be the problem right from the get-go. The gasket is probably bad if you took it off. Simple question. If you dont wanna answer it, get out of the thread. Simple enough.

Re: zx3 almost done

Posted: Mon Mar 08, 2010 1:15 pm
by Stilz
Maybe we could PUSH it into a tree. :)
Wow... Settle down Krypto. It was a generic question, not a question in regards to him or his parts.
Why are you acting so rude toward Patalrob? Did he urk you or something? I don't see how, he is a uber calm guy. If anything YOU'RE the one that should go "crash your car into a tree." Maybe you would tone it down a notch or two...
Geeze... Lots of hostility on the forums recently.
I vote uber bann session. :)

Re: zx3 almost done

Posted: Mon Mar 08, 2010 1:18 pm
by Stilz
zx3pos wrote:Just to let you know, i asked if you had it off, i did tighten it. Cause if you had it off at some point, this would be the problem right from the get-go. The gasket is probably bad if you took it off. Simple question. If you dont wanna answer it, get out of the thread. Simple enough.
X2

Re: zx3 almost done

Posted: Mon Mar 08, 2010 1:56 pm
by o2designs
hermitmaster wrote:
Patalrob wrote: Image
Is that a photo of Turbo Tom? :lol:

Yup
:lol:

Re: zx3 almost done

Posted: Mon Mar 08, 2010 2:02 pm
by o2designs
Lets just consider everyone on here warned. No more bullshit bickering between eachother about this. If you don't have some kind of advice or constructive post helping to get the issue fixed, don't post it.

-----------------------------------------------------

But back on back topic, I'm not familar with the car in question. Is this a SVT or Zetec? What codes is it throwing right now?
There was a comment about the intake being loose, have you checked all over for any leaks on the intake system?

Re: zx3 almost done

Posted: Mon Mar 08, 2010 2:12 pm
by hermitmaster
Codes are in the first post. I believe it's a standard Zetec.

Re: zx3 almost done

Posted: Mon Mar 08, 2010 2:16 pm
by o2designs
hermitmaster wrote:Codes are in the first post. I believe it's a standard Zetec.

After checking and doing a few things, its still pulling the same codes?

Re: zx3 almost done

Posted: Mon Mar 08, 2010 2:30 pm
by WASaZX3pos
I believe only the lean bank code still exists. The other stuff all depends on the outcome of this code.

Re: zx3 almost done

Posted: Mon Mar 08, 2010 2:31 pm
by WASaZX3pos
PS, thanks guys.

Re: zx3 almost done

Posted: Mon Mar 08, 2010 5:49 pm
by Patalrob
From what I understand isn't this Davis's old yellow Focus?

Re: zx3 almost done

Posted: Mon Mar 08, 2010 6:48 pm
by WASaZX3pos
Yep, whoever had it before krypto.
euro body, was boosted i believe.
for some reason it had 4dr ebrake cables in it. gotta fix that.

Re: zx3 almost done

Posted: Mon Mar 08, 2010 6:52 pm
by Steve@Tasca
zx3pos wrote:Yep, whoever had it before krypto.
euro body, was boosted i believe.
for some reason it had 4dr ebrake cables in it. gotta fix that.
Actually I think it had SVT brake cables in it, All the drum brake cars use the same cables Sedan, hatch whatever.

Re: zx3 almost done

Posted: Mon Mar 08, 2010 6:59 pm
by WASaZX3pos
either way they will not work.
You guys all know more about my car then i do, friggen crazy.

care to shed some light on the whole car in general?